Bambu Lab X1 3D Printer User Manual

Bambu Lab X1 3D Printer User Guide

Component Introduction

Bambu Lab X1 3D Printer User Guide - Component Introduction

Accessory Specification

Bambu Lab X1 3D Printer User Guide - Accessory Specification

Tool Head Unlock

Bambu Lab X1 3D Printer User Guide - Tool Head Unlock

Screen Installation

Bambu Lab X1 3D Printer User Guide - Screen Installation

Spool Holder Assembly

Bambu Lab X1 3D Printer User Guide - Spool Holder Assembly

Hot Bed Unlock

Bambu Lab X1 3D Printer User Guide - Hot Bed Unlock

Filament Loading

Bambu Lab X1 3D Printer User Guide - Filament Loading

Bambu Lab X1 3D Printer Specification

Bambu Lab X1 3D Printer User Guide - Specification Bambu Lab X1 3D Printer User Guide - Specification Bambu Lab X1 3D Printer User Guide - Specification

If you run into any issues during the guided setup, we are here to help. [email protected]

Disclaimer and Warning Bambu Lab X1 3D Printer
Thanks for purchasing a Bambu Lab product. The information in this document affects your safety and you regal rights and responsibilities. Read this entire document carefully to ensure pre per configuration before use. Failure to read and follow instructions aid warnings in this document may result in serious injury to yourself or others, damage to your Barn bu Lab product, or damage to other objects in the vicinity. This document and other collateral documents are subject to charge at the sole  discretion of Bambu Lab By using this product, you hereby signify that you have read this disclaimer and warning carefully and that you understand and agree you are solely responsible for your own conduct while using this product, and for any consequences thereof You agree to use this product only for purposes that are proper and in accordance with all applicable laws, rules and regulations, and all terms, precautions, practices, policies, and guidelines Bambu Lab has made and may make available. Bambu Lab accepts no liability for damage, or injury or any legal responsibility incurred directly or indirectly from the use of the product. The user shall observe safe and lawful practices including, but not limited to, those set forth in this document Bambu lab is a trademark of Shenzhen Tuohy Technology Co., Ltd. and its affiliated companies. Names of products. brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies.

Before You Start
The following documents have been produced to help you safely operate and make full use of your
Bambu Lab X1 Series 3D Printer
Bambu Lab X1 Series 3D Printer Disclaimer and Safety Guidelines
Bambu Lab X1 Series 3D Printer Quick Start Guide
Check t hat you have all the included parts. Please review the entire Quick Start Guide before operating the printer.
Read the Disclaimer and Warning above to understand your legal rights and responsibilities. If you have any questions or problems during the installation, maintenance, or use of this product, please contact a Bambu Lab authorized dealer.

Safety Guidelines Bambu Lab X1 3D Printer

  1. The product must be disconnected from the power supply before carrying out any installation or maintenance work
  2.  Installation and maintenance must be carried out by a skilled worker in compliance with the manufacturer’s instructions and local safety regulations
  3. Do not use multiple plug adapters or extension leads
  4. Do not touch the product with any wet part of t he body and do not operate it while barefoot
  5. Do not reach inside the appliance while it is in operation
  6. Children using or near the printer must be accompanied and supervised by a responsible adult at all times.
  7. This product is designed solely for indoor use. It should be kept in a dry environment
  8. The recommended operating temperature for the appliance is between o·c to 40″C (32″F to 104″F).
  9. The recommended humidity level is under85%
  10. The product should be positioned on a dean, stable and flat workbench
  11. The product should be kept it in a well-ventilated location Bambu Lab X1 3D Printer .

Compliance Information
FCC Compliance Notice
SuppUer’s Declaration of Conformity
Product name: X1/X1-Carbon
Model Number: PF001-NPF001-P
Responsibility Party: Shenzhen Tuozhu Technology Co.,Ltd. (Bambulab USA Incl
Responsibility Party Address: 8000 Centre Park Drive. STE 330, Austin. TX, 78754
Website: www.bambulab.com

We. Shenzhen Tuozhu Technology Co.,Ltd. (Bambulab USA Inc} . being the responsible party, declares that the above mentioned model was tested to demonstrate compliance with all applicable FCC rules and regulations Bambu Lab X1 3D Printer .

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, t here is no guarantee that interference will not occur in a particular installation Bambu Lab X1 3D Printer .
If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna Bambu Lab X1 3D Printer
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
-Consult the dealer or an experienced radio/TV technician for help Bambu Lab X1 3D Printer .

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED Compliance Notice Bambu Lab X1 3D Printer
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement
Hereby, Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment type X1/X1-Carbon is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at
the following internet address: www.bambulab.com/eum-complTance

GB Compliance Statement
Hereby, Shenzhen Tuozhu Technology Co .. Ltd. declares that the radio equipment type X1/X1-Carbon is in
compliaoce with Radio Equipment Regulations 2017. The full text of the GB declaration of conformity is available at the following internet
address: www.bambulab.com/euro-compliance
Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed.3.,as described in Laser
Notice No.56,dated May8,2019 Bambu Lab X1 3D Printer

Bambu Lab X1 3D Printer User Guide - Certified icon

www.bambulab.com
Copyright© 2022 Bambu Lab All Rights Reserved.

Bambu Lab Logo

Leave a comment

Your email address will not be published.