Fary 21.6 in. Satin Nickel Ceiling Fan
with Light User Manual

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide

WARNING
READ AND SAVE THESE INSTRUCTIONS To avoid fire, shock and serious personal injury, follow these instructions. Fary

  1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly  diagrams.
  2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag.to the service panel Fary
  3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always tum off the power to the ceiling fan before servicing
  4. Do not insert anything into the fan blades while the fan is operating
  5. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. Fary

ADDITIONAL SAFETY INSTRUCTIONS

  • To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades. Fary
  • All wiring and installation procedures must satisfy National Electrical Codes (ANSI/NFPA 70) and Local Codes. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
  • The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to exceed Fary 35 lbs. or 15. 9 kgs. ) . See page 5 of owner’ s manual for support requirements. Consult a qualified electrician if in doubt.
  • The fan must be mounted with the fan blades at least loft from the floor to prevent accidental contact with the ceiling fan. Fary
    Follow the recommended instructions for the proper method of wiring your ceiling fan, If you do not have adequate electrical
  • knowledge or experience, have your fan installed by licensed electrician. Fary
  • Suitable for use with solid-state speed controls.
  • This fan is to be used in indoor dry or damp location only.
  • For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected to an equipment-grounding conductor. Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconCAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING: To reduce the risk of electric shock, this fan must be installed with a general use, isolating wall. Fary

This product is designed to use only those parts supplied with this product and/or accessories designated specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property damage. Fary

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets. balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades. Fary

Mount to an outlet box marked acceptable for fan support of15. 9kg (35 lbs) or Less.

ADDITIONAL SAFETY INSTRUCTIONS

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch Doing so could result in damage to the ceiling fan’s remote control unit. This device complies with Part 15 of the FCC Rules Operation is subject to the following two condition: so (1 ) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. if the intentional radiator con be classified as a Class B digital device or a PC peripheral, then shall include the following or equivalent. Fary

NOTE: This equipment has been tested one found to comply with the limits for Class B digital device. pursuant to part 15 of the FCC Rules, These limits ore designed to provide reasonable protection against harmful interference in residential installation This equipment generates, uses one can radiate radio frequency energy and, if nor
installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Fary

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

For a Class A digital device, statements of 15. 105 (a) must be included when appropriate for the device in question

Warranty

We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. We also warrant the light kit, to be free from defects in workmanship and material present at time of shipment from the factory for a period of five years after the date of purchase by the original purchaser, excluding any glass or acrylic components and wooden blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. We hereby disclaim any and all warranties, including but not limited to those of merchant ability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The manufacturer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer. Fary

ENERGY EFFICIENT USE OF CELING FANS

Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.

Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle of the room and at least 10 feet from floor to the blade and 18 inches from wall to the blade. If ceiling height allows, install the fan 8-9 feet from floor to the blade for optimal airflow. Consult your era group Retailer for optional mounting accessories.

Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the clockwise direction. The airflow produced by the ceiling fan creates a wind-chill effect. making you “feel” cooler. Select a fan speed that provides a comfortable breeze, lower speed consume less energy.

Winter Season: Reverse the motor and operate the ceiling fan at low speed in the counter clock-wise direction. This produces a gentle updraft, which forces warm air near the ceiling down into the occupied space. Remember to adjust your thermostat when using your ceiling fan-additional energy and dollar savings could be realized with this simple steps!

ELECTRICAL AND STRUCTURAL REQUIREMNTSI

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 HZ, 15 Amp Circuit. Electrical code requires use of a fan-rated outlet box to support the extra weight and motion associated with a ceiling fan. A fan-rated box will be labelled as such and typically supports up to a 70Ibs ceiling fan. Fan-Rated Outlet Boxes vary in ratings and design. Ensure the ratings of your ceiling fan outlet box meet the requirements for the ceiling fan being installed. Figure 1, Figure 2 and Figure 3 depicts different structural configurations that may be used for mounting the outlet box.

Low-profile use (Figure 1)
A12-in. -deep pancake box is meant to be screwed to a joist or block. It’s used if only one cable is coming into the box. It is also avail-able in a saddle-mount configuration.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Figure 1

Deep-profile use (Figure 2)
A 2-1-in. -deep box can be attached to blocking between joists and is roomy enough to handle more than one cable.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Figure 2

Brace use (Figure 3)
Paired with a deep box, this hanger is meant to span between two joists and takes the place of wooden blocking.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Figure 3

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING: To reduce the risk of fire. electrical shock, or personal injury. mount fan to outlet box marked acceptable for fan support of 15. 9 kg (35 lbs) or less. Use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need tube replaced. Consult a qualified electrician if in doubt.

If your fan is to replace an existing light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING:
Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local code sand the ceiling fan must be properly grounded as a precaution against possible electrical shock. Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING:
To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING:
Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage to the ceiling fan’s remote control unit. Fary

Angled ceiling use place (Figure 4)
Angled ceiling maximum 20 angle

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Figure 4

NOTE: You may need a longer downrod (sold separately) to maintain proper clearance when installing on steep, sloped ceiling. Fary

PRE-INSTALLATION

This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan Fary
Tools Needed for Assembly (Not Included)

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Tools Needed for Assembly

MATERIALS NEEDED

Wiring outlet and connectors of type required by the local code. The minimum wire would be a 3-con (2-wire with ground) of the following size:

Installed wire length
Up to 50 ft.
50-100 ft.

Wire Size A. W. G
12
12

NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing contact your local retailer.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING:
Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page10) . If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician. Fary

UNPACKING INSTRUCTIONS

PACKAGE CONTENTS
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted. Fary

WARNING:
Do not install or use fan if any part is damaged or missing. This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by earn group. Substitution of parts or accessories not designated for use with this product by era group could result in personal injury or property damage.

  1. Check to see that you have received the following parts: Fary

NOTE: If you are uncertain of part description. refer to exploded view illustration provided on the last page of this install manual.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Check to see that you have received the following parts

HOW TO ASSEMBLE YOUR CEILING FAN

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to assemble Your ceiling fan

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to assemble Your ceiling fan

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to assemble Your ceiling fan Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to assemble Your ceiling fan

HOW TO HANG YOUR CEILIN

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to Hang your Ceiling

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to Hang your Ceiling

PAIR REMO TE & RECEIVER

NOTE:
The remote unit has 16 different code combinations. To prevent possible interference from or to other remote units, simply change the combination code in the remote and receiver.

To set the code on receiver unit, slide dip switches to the same positions as set on the remote. (Figure 1) Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Pair Remote & Receiver

NOTE:
Factory default setting is dip switches all up. Do not use this position. Fary

WIRE THE CEILING FAN

WARNING:
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. (Figure 2)

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Wire the ceiling fan

NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, asit must be grounded for safe operation. Fary

WIRING YOUR CEILING FAN

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Ceiling

  • Slide the receiver into the hanger bracket.
  • Connect green wires from hanger bracket and downrod and wave filter to bare (ground) wire using wire connector. Fary
  • Connect black wire from wove filter unit marked “AC IN L “to block supply wire using wire connector.
  • Connect white wire from wave filter unit marked “AC IN N “to white supply wire using wire connector.
  • Connect white wire from receiver unit marked “TO MOTOR N” to white wire from fan using wire connector supplied with receiver unit.
  • Connect black wire from receiver unit marked “TO MOTOR L “to black wire from fan using wire connector supplied with receiver unit.
  • Lastly. connect blue wire from receiver unit to the blue fan light wire using wire connector supplied with receiver unit. (Figure 3) Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Hardware use

NOTE:
If you feel that you do not have enough electrical wiring knowledge or experience. have your fan installed by a licensed electrician. Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Wire your ceiling fan

HOW TO INSTALL YOUR CANOPY HOUSING

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to install your canopy housing

HOW TO OPERATE YOUR CEILIN FAN

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to operate your ceiling fan

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to operate your ceiling fan

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to operate your ceiling fan

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - How to operate your ceiling fan

Fary MAINTENANCE

Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning. use only soft brush or lint free cloth to avoids catching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish.

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconCAUTION
Do not use water when cleaning your ceiling fan. It could damage the motor or the finish and create the possibility of electrical shock. Fary

TROUBLESHOOTING

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Warning or Caution iconWARNING: For your own safer tum off power at fuse box or circuit breaker before trouble shooting your fan. Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Troubleshooting

REPLACEMENT AND DISASSEMBLY DIAGRAM OF FAN BLADES.

Fan blade cleaning and disassembly installation diagram. wipe with dry cloth or chicken blanket Do not wash with water( figure 1) Fary

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Fan blade cleaning

EXPLODED REVIEW ILLUSTRATION

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Guide - Exploded Review Illustration

NOTE:
The illustration shown is not scale or its actual con gyration may vary. Product/parts are subject to change with out notice.

Download PDF

Fary 21.6 in. Satin Nickel Ceiling Fan with Light User Manual PDF Download

Leave a comment

Your email address will not be published.