GLEN LZX-F16682 Infrared Thermometer
User Manual

GLEN LZX-F16682 Infrared Thermometer User Guide

Introduction

* Your new Non-contact Infrared Thermometer uses advanced infrared (IR) technology to measure temperature instantly and accurately on the forehead or object.

* Easy to use and less measurement time This thermometer does not need to contact body or object to ensure the safety and hygiene. Its ergonomic design makes this thermometer simple and very easy to check the temperature. It only takes 3 seconds to take measurement and reading.

* Body and object modes
This thermometer can measure temperature of body and object. Measuring range of object mode is 0.0 to 100.0 °C (32.0 °F – 212.0 °F). This means it can take body as well as object surface temperature as mentioned below:
– Surface temperature of milk in the bottle
– Surface temperature of baby bath
– Environment temperature

* Alarm sounds when body temperature is over 38.5°C.

* Memory function
It stores up to 1 sets recent measurement data.

* Auto power off
Automatically power off if left idle for 60 seconds.

* Measurement
Measurement time interval is 15 seconds and the measurement distance Is within 5-8 cm.

Please read the manual carefully before you using the unit, and keep for future reference.

Safety Information

* This thermometer is not intended to substitute for a consultation with your physician. The forehead scan temperature serves for reference only. It can not measure fever.
* Basic safety precautions should always be observed, especially when the thermometer is used on or near children and disabled persons.
* Please place the device out of reach of children.
* Avoid direct sunlight.
* Do not touch the lens.
* No modification of this device is allowed.
* Keep all packing material safely or dispose off as swallowing of packing bag, battery, battery cover may cause the suffocation.
* Please do not use any cleaning agent, alcohol or petrol to clean the unit. Please treat is gently and prevent the falling from a high place.
* Please do not immersed it in liquid.
* Never leave battery in the battery compartment for a long time
without use, as they may leak and cause damage to the unit.
* Please take off the battery if you do not intend to use within 3 months. Replace with new batteries if the unit display a low battery symbol.
* Do not mix the old and new batteries together.
* To ensure the correct use of the product, basic safety measures should always be followed including the warning and the caution symbols listed in the instruction manual:

GLEN LZX-F16682 Infrared Thermometer User Guide - Symbol Descriptions

GLEN LZX-F16682 Infrared Thermometer User Guide - Disposal iconWARNING:
A Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliance are disposed of in landfills or dumps, hazardous substances
can leak into the ground water and get into the food chain, damaging your health and well-being.

Classification

  1. Internally powered equipment;
  2. Type BF applied part;
  3. Protection against ingress of water: IPXO;
  4. Not category AP/APG equipment;
  5. Mode of operation: Continuous operation;

Note: the user must check that the equipment functions safely and ensure that ii is in proper working condition before its being used.

Product Structure

* Body

  1. Display Screen
  2. Mode switch
  3. Sensor probe
  4. Down(-) Button
  5. Up(+) Button
  6. Setting Button
  7. START/STOP Button
  8. Battery Cover

GLEN LZX-F16682 Infrared Thermometer User Guide - Body

* Display

GLEN LZX-F16682 Infrared Thermometer User Guide - Display

  1. Object temperature indicator
  2. Body temperature indicator
  3. Temperature unit
  4. Memory mode
  5. Low battery indicator
  6. Sound indicator
  7. Temperature reading

Battery Installation

  1. Remove the battery cover from the battery compartment as the arrow direction accordingly.
  2. Insert 2pcs 1.5V AAA Alkaline batteries, and ensure each battery is in the proper direction.
  3. Close the battery cover.

GLEN LZX-F16682 Infrared Thermometer User Guide - Battery Installation

Low battery and replacement
During power on, the low battery symbol will GLEN LZX-F16682 Infrared Thermometer User Guide - Low battery and replacement display once the unit starts to work, and you should replace with new batteries, otherwise the unit cannot work.

Battery type and replacement
Please use 2pcs. of AAA identical 1.5V alkaline batteries. Do not use the batteries beyond their expiry date. Please remove the batteries if you do not need to use for long time.

WARNING
Dispose the battery in accordance with all federal, state and local laws. To avoid fire and explosion hazard. do not burn or incinerate the battery GLEN LZX-F16682 Infrared Thermometer.

Setting

How to set

* Press “SET”, display will showed F-1, press”+””-” can select °F/°C.
* Press “SET” again, display will showed F-2, press “+” “-” can select on/off.

GLEN LZX-F16682 Infrared Thermometer User Guide - How to set

Use of the Unit

Pre-measurement
About Normal Body Temperature & Fever GLEN LZX-F16682 Infrared Thermometer
The temperature in the forehead and temple area differs from the internal temperature, which is taken orally. Vasoconstriction, an effect which constricts the blood vessels and cools the skin, can occur during the early stages of a fever. In this case, the temperature measured by the non-contact thermometer may be unusually low. If the measurement therefore does not match the patient’s own perception or is unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal body temperature using a conventional oral or rectal thermometer GLEN LZX-F16682 Infrared Thermometer.

Body temperature can vary from one Individual/person to next. It also varies by location on the body and time of day. Below shows the statistical normal ranges from different sites GLEN LZX-F16682 Infrared Thermometer.

Please keep in mind that temperatures measured from different sites, even at the same time, should not be directly compared. Fever indicates that the body temperature is higher than normal. This symptom may be caused by infection, overdressing or immunization. Some people may not experience fever even when they are ill.

These include, but are not limited to, infants younger than 3 months old, persons with compromised immune systems, persons taking antibiotics, steroids or antipyretics (aspirin, ibuprofen, acetaminophen), or persons with certain chronic illnesses. Please consult your physician when you feel feverish even if you do not have fever GLEN LZX-F16682 Infrared Thermometer.

GLEN LZX-F16682 Infrared Thermometer User Guide - Table 1

Use of the Unit

Measuring procedure
As a Body Thermometer

  1. Select Body Mode, the temperature unit flashes GLEN LZX-F16682 Infrared Thermometer.
  2. Move the probe close to the forehead, make sure the probe is flat and take measurement with a distance within 5-8 cm Press Start/Stop button.
  3. The measurement will be finished in seconds, when II has been completed, you can hear a short beep, at the same time, the reading will appear on GLEN LZX-F16682 Infrared Thermometer

GLEN LZX-F16682 Infrared Thermometer User Guide - Measuring procedure

Note:
– If the reading is s 37.5’C(99.5’F) and~ 32’C(89,6’F), the Display will show with green backlight GLEN LZX-F16682 Infrared Thermometer
– If the reading is ~set fever value ;;, 37.S’C and s 38.S’C, the display will show yellow backlight
– If the reading is set fever alarm value ~ 38.S’C and s43’C, the display will show together with a long beeps, the red backlight lasts for alarm.
– Only after the unit ‘C or ‘F starts to flash again, it can continue to take measurement.
-As the forehead measurement temperature is likely to be affected by sweat, oil and the surroundings, the reading shall be taken as a reference only.
– If the probe is placed at an angle close to the forehead measurement, the reading will be affected by surrounding temperature.
– Babies skin reacts very quickly in the ambient temperature. Therefore, do not take their temperature with the non-contact thermometer during/after breast feeding, because the skin temperature maybe lower than the internal body temperature.
– The thermometer will automatically turn off if left idle for 60 seconds GLEN LZX-F16682 Infrared Thermometer.

Measuring procedure
As Object Thermometer

  1. Select Object Mode, the temperature unit flashes.
  2. Move the probe close to the object, make sure the probe is flat and take measurement with a distance within 5-8 cm. Press the Start/Stop button to take measurement
  3. The measurement will be finished in 1 second, when it has been completed, you can hear a short beep, at the same time, the reading Will appear on the display GLEN LZX-F16682 Infrared Thermometer

GLEN LZX-F16682 Infrared Thermometer User Guide - As object Thermometer

Note:

* As the object scan temperature is likely to be affected by the surroundings, the reading shall be taken as a reference only.
* If the probe is placed at an angle close the object scan, the reading will be affected by surrounding temperature.
* The thermometer will automatically tum off if left idle for 60 seconds GLEN LZX-F16682 Infrared Thermometer.

Trouble Shoot

Error indicators
The following symbols will appear on the display when measurement is abnormal GLEN LZX-F16682 Infrared Thermometer

GLEN LZX-F16682 Infrared Thermometer User Guide - Troubleshoot GLEN LZX-F16682 Infrared Thermometer User Guide - Troubleshoot

Care and Maintenance

Care for the main unit
– Keep the unit in the storage case when not in use GLEN LZX-F16682 Infrared Thermometer.
– Clean the unit with a soft dry cloth. Do not use any abrasive or volatile cleaners.
– Never immerse the unit or any of its component in water GLEN LZX-F16682 Infrared Thermometer.

Maintenance

GLEN LZX-F16682 Infrared Thermometer User Guide - Maintenance

Note: We will not be responsible for any quality problem if you do not care and maintain the product as instructed GLEN LZX-F16682 Infrared Thermometer.

Specification

GLEN LZX-F16682 Infrared Thermometer User Guide - Specifications

GLEN LZX-F16682 Infrared Thermometer WARRANTY

This GLEN Infrared Thermometer is fully warranted against any defect arising out of defective materials or faulty workmanship for a period of 1 year from the date of purchase. Should any defect develop in this product, the customer should bring the product to the nearest authorised service centre, where the company undertakes to get the product repaired free of charge GLEN LZX-F16682 Infrared Thermometer.

This Warranty Is Not Valid If:

  • The Use And Care Instructions Have Not Been Followed.
  • Defects Are Caused By Accident, misuse, abuse or commercial use.
  • The repair work is carried out by person not authorised by the company.
  • Any modification or alteration of any nature is made in the product.
  • Normal wear and tear of the product is not covered under warranty
  • The Bill/Cash memo and copy of warranty card is not presented.

Under no circumstances, whether based on limited warranty or otherwise shall the company be liable for incidental, special or consequential damages. Use of product indicates acceptance by you of the aforesaid terms and conditions GLEN LZX-F16682 Infrared Thermometer.

PRODUCT NAME : Infrared Thermometer

SERIAL NO.: ________________
DATE OF PURCHASE: __________________

DEALER’S STAMP & SIGNATURE

GLEN Logo

Manufactured by
Glen Appliances Pvt. Ltd.
Plot No. 919, Sector 68, IMT, Faridabad, Haryana 121 004. INDIA
Customer Care & H.O.
1-34, DLF Indl. Area, Phase 1, Farldabad 121 003 (Haryana), INDIA.
E-mail : [email protected] Website : www.Qlenindia.com
CUSTOMER CARE 92666 55555

Leave a comment

Your email address will not be published.