SHARP VISION EMSV1196 9-Inch
Wireless Color 2.4G Digital LCD Monitor User Manual

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual

1. Precautions

  • Storage and Keeping
  1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30-+80°C, and the operating temperature is -20-+70 °C. The humidity is Rh90%.
  2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places.
  3. Never use this device in environments with excessive moisture, dust or smoke.
  4. Avoid dropping or striking this device.
  5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts.
  6. Never puncture, scratch or use abrasive cleaning materials on this device.
  7. Do not place cables where they may be pinched or stepped on.
  8. Leave at least a 2″ space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device.
  9. The monitor is not designed to be waterproof.
  • Operating Precautions
  1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
  2. Make sure all cables are connected properly. Observe polarity. Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the device.

⚠ Warning!

  1. High voltage is present within the monitor. The opening of the case should be by professionals.
  2. Do not watch the video while driving unless you are monitoring the rear view camera display.

⚠ Special Notice
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common . phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.

  • Maintenance
  1. Remove all the cable connections from the monitor before cleaning the device.
  2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Safety icon

  • Declaration of conformity

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Declaration of conformityThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.

2. Features

  1. TFT LCD monitor with wide angle view and high resolution display.
  2. NORMAL, MIRROR, FLIP and MIR-FLIP viewing available.
  3. Split mode, auto-scan mode and single-display mode available.
  4. Auto pairing: Auto pairing happens when camera is activated.
  5. Support 4-channel composite and single-channel recording in AV! signal format.
  6. Auto dim function available.
  7. Full-function remote control.
  8. 4 wireless camera input.
  9. Multiple video formats: PAL/ NTSC.
  10. Wide voltage input: 10 – 32V.
  11. On-board speaker.
  12. Auto switch to the working channel when trigger is activated.

3. Technical Specifications

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Technical Specifications

⚠ Special Notice 
All specification are subject to change without notice.

4. Accessories

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Accessories

⚠ Special Notice
Accessory supply may be different for different application.

5. Parts Identification

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Parts Identifications

6. Remote Control Operation

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Remote Control Operation

  • MUTE(Mute)
    Press to select MUTE or enable sound
  • POWER(Power switch)
    Press to turn on/off the monitor
  • OK
    Press OK button to enter menu item or save user settings. Press OK button – shortcut for start/stop recording
  • MENU
    Press to show menu or exit menu
  • ◁ VOL
    Volume decrease and menu selection left
  • ▷ VOL
    Volume increase and menu selection right
  • SEL
    Jump key selector. Fast jump to the display mode specified by SYSTEM SETUP – JUMP KEY
  •  PAIR
    Fast pairing when camera is activated
  • SYS
    PAL/ NTSC TV system selector
  • MIR
    MIR-Flip selection

7. Basic Operation

7.1.lnstallation of Center Mounting Bracket:

  1. Adjust monitor level by sliding the support to the desired height.
  2. Adjust the angle of the monitor and tighten the knob on the center mounting bracket.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Installation of Center Mounting Bracket

7.2.lnstallation of U-support Bracket

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Installation of U-support Bracket

7.3.Reversing Display:

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Reversing Display

7.4. Volume selection under quad view

  • 7.4.1. Check the volume icon on the top right area under single channel mode. It stands for audio out for the selected channel.
  • 7.4.2. Press ◁ or ▷ to select the channel for audio out.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Volume selection under quad view

8. Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Menu

  • Auto pairing:
  1. Choose the channel that needs to be set up, and the monitor display the message “PAIRING START 50” and a counter that counts down 50s.
  2. Within the countdown, power the camera.
  3. The monitor and cameras will synchronize themselves with each other after the camera is powered for 5s.
  4. If pairing is completed, the video will be displayed. If it is failed, a message “No Signal” will be displayed. Repeat the pairing procedure.
  • Manual pairing:
  1. Choose the channel that needs to be set up, and the monitor display the message “PAIRING START 50” and a counter that counts down 50s.
  2. Press the pairing button on the power-on camera.
  3. The monitor and cameras will synchronize themselves with each other.
  4. If pairing is completed, the video will be displayed. If it is failed, a message “No Signal” will be displayed. Repeat the pairing procedure.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Manual Pairing

9. Recording Time

With SD cards in different capacities, please refer to the table below for recording time under 3 different image modes.
This table is for reference only. Data may vary under different environments.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Recording Time

10. Installation Tips

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Installation Tips

11. Troubleshooting

The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate request for repair.

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Troubleshooting

CAMERA SPECIFICATION

SHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Camera SpecificationSHARP VISION EMSV1196 2.4G Digital 9-Inch Wireless Color LCD Monitor Instruction Manual - Camera Specification

Download PDF

Leave a comment

Your email address will not be published.