KAIWEETS HT100B Voltage Tester User Manual

KAIWEETS HT100B Voltage Tester User Manual

KAIWEETS HT100B Voltage Tester User Manual - Warning Risk of Electric shock iconWARNINGS
With this device, life-threatening voltages are tested, so special care is required!

  • Always first test the voltage tester on a known circuit to make sure it works!
  • When checking uninsulated contacts, wear safety shoes to prevent electric shock.
  • When checking uninsulated contacts, hold the tester and make sure your fingers are behind the anti-slip guard.
  • Do not use the device if:
    – The screen is not lit;
    – Damage is evident;
    – The tip is not intact.
  • Do not put the device in more than 1000V
  • This equipment can only be used indoors and should be protected from water, high air humidity and heat.
  • ATTENTION: Even without indication, the voltage could still be present. The voltage detector indicates the effective voltage when a supply voltage generates enough intensive electrostatic field. If the field is very weak, the voltage detector can’t detect the existence of voltage.
  • We do not accept any liability for property damage or personal injury caused by incorrect operation or failure to follow safety instructions. In this case, any warranty claim will lapse.

Product Overview

  1. Probe (NCV sensor)
  2. Flashlight
  3. Signal indicator
  4. LCD screen
  5. Power button(red)
  6. S button (green) Sensitivity (short press) LED lamp (long press)
  7. Battery cover

KAIWEETS HT100B Voltage Tester User Manual - Product Overview

Operation

Turning on / off

Press and hold the power key for more than 2 seconds. A beep sounds and the display lights up. Press the power button again and the tester will turn off. After 3 minutes of non-use, the tester automatically powers off to conserve battery life. The tester is now deactivated and is not operational.

Checking for the presence of AC voltage

KAIWEETS HT100B Voltage Tester User Manual - Warning Risk of Electric shock iconPrior to each use, test on known live circuit to verify tester functionality!
Keep the tester’s tip near the AC voltage. When a voltage is detected, a beep sounds and the tip lights up red. As the intensity of the voltage signal changes, the bar graph on the screen becomes higher or lower and the frequency of blinking and beeping becomes faster or slower with the signal intensity.

KAIWEETS HT100B Voltage Tester User Manual - Checking for the presence of AC voltage

 

The signal intensity is affected by the distance from the voltage. The further the tester is from the circuit, the weaker the signal becomes.

Dual range

When the tester is turned on, it is in low-sensitivity mode (48 ~ 1000V). Briefly press the green button to enter the high sensitivity mode (12 ~ 1000V). Refer to the following table for each mode.

KAIWEETS HT100B Voltage Tester User Manual - Dual range

KAIWEETS HT100B Voltage Tester User Manual - Low & High-Sensitivity Mode

In high-sensitivity mode, the tester will be more sensitive and show voltage indication at a further distance away from high voltage source than in low-sensitivity mode.

Identify null and live wire

Keep the individual cables as far away from each other as possible and read the signals.

KAIWEETS HT100B Voltage Tester User Manual - Identify null and live wire

The screen turns red and shows a high voltage symbol when the voltage is higher than 90V. The neutral wire and live wire should not be distinguished by the screen color, but by the detected signal intensity. The live wire causes stronger signals and the neutral causes weaker signals.
It is recommended to activate the high sensitivity mode during identification.

Breakpoint testing

Activate the high sensitivity mode, move the tester’s NCV tip along the cable, the voltage alarm disappears when detected a break point, as shown in Figure 2.

KAIWEETS HT100B Voltage Tester User Manual - Breakpoint testing

Caution: Do not use it on cable ducts or metal-clad cables.

LED Flashlight

Press and hold the green button for more than 2 seconds to turn the LED light on and off. If no button on the tester is pressed and no voltage signal is detected. After 3 minutes, it will automatically shut down to save power.

Low battery indicator

If the battery voltage is less than 2.5 volts, the display will show the KAIWEETS HT100B Voltage Tester User Manual - Low Battery icon symbol. If the battery voltage is less than 2.3 volts, the tester automatically turns off.

Technical specifications

Voltage: …………………………………. ……………………….AC 12~1000V,50/60Hz
Operating temperature:……………………………………………………………..0~40℃
Storage temperature:……………………………………………………………-10~50℃
Humidity:…………………………………………………………………………………≤95%
Operating altitude:………………………………………………………………….≤2000m
Security level:……………………………………CE, CAT III 1000V, CAT IV 600V
Batteries:…………………………………………………………………………2×1.5V AAA

Battery replacement

KAIWEETS HT100B Voltage Tester User Manual - Warning or Caution iconRotate the battery cover off body, remove the batteries, and insert the positive terminal of the new battery toward the tip of the tester. Rotate cap to the body until it is fully seated. Before locking, do not use the tester to test the electricity to avoid electric shock.

KAIWEETS HT100B Voltage Tester User Manual - Battery replacement

Cleaning

Use only a soft, slightly damp cloth to clean the device, never use chemicals or abrasives, alcohol, ammonia or cleaners containing solvents to clean tester. Make sure that the device is completely dry before use.

Three years warranty

The KAIWEETS electronic test and measurement devices are guaranteed for three years from the date of purchase.

After-sale: [email protected]

Download PDF

KAIWEETS HT100B Voltage Tester User Manual PDF Download

Leave a comment

Your email address will not be published.