BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE
CLEANER User Manual

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User ManualBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual -

IMPORTANT SAFETY INSTRUCTIONS

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - note READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE.
When using an electrical appliance, basic precautions should be observed, including the following:

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - warning WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

  • Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
  • Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
  • Use indoors only.
  • Do not allow to be used as a toy. Close attention is necessary when used by or near children.
  • Do not use for any purpose other than described in this user guide. Use only manufacturer’s recommended attachments.
  • Do not use with damaged cord or plug. If appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
  • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
  • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  • Do not handle plug or appliance with wet hands.
  • Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
  • Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
  • Turn OFF all controls before plugging or unplugging appliance.
  • Use extra care when cleaning on stairs.
  • Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
  • Do not use appliance in an enclosed space filled with vapors given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
  • Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
  • Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
  • Use only BISSELL® cleaning formulas intended for use with this appliance to prevent internal component damage. See the Cleaning Formulas section of this guide.
  • Do not immerse. Use only on surfaces moistened by the cleaning process.
  • Keep appliance on a level surface.
  • Do not carry the appliance while in use.
  • Do not use without filters in place.
  • Risk of injury. Brush may start unexpectedly. Unplug before cleaning or servicing.
  • To reduce the risk of injury from moving parts – unplug before servicing.

SAVE THESE INSTRUCTIONS
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
COMMERCIAL USE OF THIS APPLIANCE VOIDS THE MANUFACTURER’S WARRANTY.

⚠️WARNING
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.
GROUNDING INSTRUCTIONSBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Grounded
This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

What’s in the Box?

Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - What’s in the Box.

Assembly

Go to support.BISSELL.com for assembly videos.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Insert handle into body ofBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Align clean water tank withBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Wrap the cord around the
1. Insert handle into body of machine until it clicks into place.2. Align clean water tank with the grooves on the back of the machine and slide it until it clicks into place.3. Wrap the cord around the Quick Release™ Cord Wrap and the lower cord wrap.

Note: To easily unwrap the cord, turn the Quick Release
Cord Wrap down to remove the cord.

Changing the Brush Roll

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - FreshStart™ MultiSurface Brush Roll

FreshStart™ MultiSurface Brush Roll
Maintain freshness of the brush roll while removing tough, sticky messes and picking up dry debris.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Wood Floor Brush Roll

Wood Floor Brush Roll
Gently clean sealed hard floors.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Area Rug Brush Roll

Area Rug Brush Roll
Pick up dry debris and pet hair.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - FreshStart PET

FreshStart PET Multi-Surface Brush Roll
Maintain freshness of the brush roll while removing tough, sticky messes and picking up pet hair and dry debris.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Grab the front of the brushBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Remove the brush roll by byBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Reinstall by placing the end
4. Grab the front of the brush window and pull upward to
remove.
5. Remove the brush roll by by  pulling the tab.6. Reinstall by placing the end  of the brush into the right side of the foot.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Press the tab of the brushBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Replace the brush rollBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Press the window back so it
7. Press the tab of the brush down so it locks into place.8. Replace the brush roll window by lining up tabs on the edges of the foot.9. Press the window back so it clicks into place.

Filling the Clean Water Tank

Visit support.BISSELL.com to watch additional how-to videos.

Keep plenty of CrossWave® formulas on hand so you can clean whenever it fits your schedule.

Note: Only use CrossWave formulas in your machine. Other formulas or household cleaners may harm the machine. Do not use hard floor formula on area rugs or carpet.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Pull the clean water tank upBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Unscrew the cap from theBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Choose your formula

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - qr
http://scn.by/9t9ab0htw8nrnl
1. Pull the clean water tank up to remove.2. Unscrew the cap from the bottom of the tank.3. Choose your formula*. Scan the QR code with your
smartphone camera or visit BISSELL.com for formulas.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - The clean water tank has a Large Area volume and a SmallBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Screw the cap back on,
4. The clean water tank has a Large Area volume and a Small Area volume. Pick the one that best suits the space that you would like to clean.

The Large Area fill lines are for areas up to 700 sq ft.
The Small Area fill lines are for areas under 350 sq ft.

Use warm (140°F/60°C max) tap water and add the appropriate BISSELL formula.

5. Screw the cap back on, align clean water tank with the grooves on the back of the machine and slide it until itclicks in to place.

*Compatible BISSELL formulas include: Multi-Surface, Wood Floor, Area Rug, PET Multi-Surface with Febreze Freshness, Hard Floor Sanitize, PET Clean + Natural Multi-Surface Certain trademarks used under license from The Procter & Gamble Company or its affiliates.

ATTENTION This machine is designed to be used on sealed hard floors and area rugs.

⚠️WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning formula intended for use with the hard floor device.

Cleaning Your Floors

Visit support.BISSELL.com to watch additional how-to videos.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - To turn the machine ON, pressBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Recline to start the brushBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Before each use, hold the
1. To turn the machine ON, press the hard floor or rug button.

Hard Floor: Everyday messes on sealed hard floors, like
tracked-in mud, spilled cereal and milk, coffee, and more.

Rug: Refresh and clean dry messes, like crumbs, dirt, hair,
and more.

2. Recline to start the brush roll spinning. Brush roll will not
spin when machine is upright.
3. Before each use, hold the solution spray trigger for 10
seconds to prime the system with cleaning solution.LED lights will illuminate when holding the solution spray
trigger. Bubbles will appear in the brush roll window when the solution is flowing.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Hold the solution sprayBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Release the trigger andBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Press the rug or hard floor
4. Hold the solution spray trigger to apply solution on
forward and backward passes.
5. Release the trigger and make a backward pass without dispensing solution. To dry floors faster, make additional
dry passes.
6. Press the rug or hard floor button to turn the machine OFF.

Cleaning with Hard Floor Sanitize Formula
Please read “DIRECTIONS FOR USE” on Hard Floor Sanitize formula label. Use on hard nonporous floors only.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Remove visible soil beforeBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Allow formula to remain wetBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - With the trigger released,
1. Remove visible soil before cleaning. Hold trigger down to
apply solution on to the floor.
2. Allow formula to remain wet on the floor for five minutes. Additional wet passes may be necessary.3. With the trigger released, make forward and backward
passes to extract solution.

Emptying the Dirty Water Tank

Go to support.BISSELL.com for a full list of how-to videos

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Press the button on top ofBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Hold the top of the tankBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - . Pour dirty water down the
1. Press the button on top of the tank, grab the front handle
and pull the tank out.
2. Hold the top of the tank near the sides of the filter and
pull up to remove.
3. Pour dirty water down the sink and rinse the tank.

Using the Storage Tray & Clean Out Cycle

Visit support.BISSELL.com to watch additional how-to videos.

Note: The Clean Out Cycle can be run in the storage tray or on sealed hard floors.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Align arrows on the storageBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Make sure there is enoughBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Optional Add FreshStart™
1. Align arrows on the storage tray with arrows on the brush
roll drying tray and slide into place.
2. Make sure there is enough solution in the clean water
tank to run the self cleaning cycle. Empty the dirty water
tank prior to starting the selfc leaning cycle.
3. Optional: Add FreshStart™ Clean-Out Formula to max fill line on tray.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - To begin the self-cleaningBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - The Clean Out Cycle will runBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Once the clean out cycle
4. To begin the self-cleaning cycle, press and hold the Area
Rug / Clean Out Cycle button for 3 seconds.
5. The Clean Out Cycle will run for 40 seconds.

Note: To stop or pause the cycle, press the Area Rug / Clean Out Cycle button. Press again within two minutes to continue.

6. Once the clean out cycle has completed, empty the
dirty water tank and follow the after-cleaning care steps on
page 7.

 

ATTENTION Do not overwet carpet or hardwood floors. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.

After-Cleaning Care

Visit support.BISSELL.com to watch additional how-to videos.

Important: The filter must be cleaned and dried after every use to maximize suction and performance. Replace the filter every 3 months.

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Remove and empty the dirtyBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Hold the top of the tank 2BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Wash filter and screen
1. Remove and empty the dirty water tank following steps 1-3 on page 6.2. Hold the top of the tank near the sides of the filter and pull up to remove.3. Wash filter and screen with warm water and mild detergent.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Rinse the float at theBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Remove the brush roll. SeeBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Hand wash with mild
4. Rinse the float at the bottom of the top of the dirty water tank cover.5. Remove the brush roll. See page 3 for instructions.6. Hand wash with mild detergent. Put the brush roll in the drying tray.
BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Wipe out the brush rollBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - Leave all parts out to dry
7. Wipe out the brush roll chamber.8. Leave all parts out to dry before reassembling.

Storing Your Machine

For more helpful maintenance tips, check out support.BISSELL.com.

Store machine in a protected, dry area. Since this product uses water, it must not be stored where there is danger of freezing. Freezing will damage internal components and may void the warranty.

NOTICE To reduce the risk of a leaking condition, do not store machine where freezing may occur. Damage to internal components may result.

⚠️WARNING To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

Troubleshooting

Below are some of the issues you may run into. If you don’t see the issue you’re experiencing below, visit support.BISSELL.com.

ProblemPossible CauseRemedies
Reduced or no sprayClean water tank may be empty or seated incorrectlyRefill and reinstall tank.
System isn’t completely primed.Hold trigger for 10 to 15 seconds to make sure the solution has flowed to the spray tips.
Brush window is not latched in place.Unplug machine and reinstall brush window.
Not holding trigger to spray solution.Hold trigger continuously while using the machine.
Loss of suction or streakingTanks may not be seated properlyRemove both tanks and reseat them so they fit properly on the machine.
Dirty water tank is full.Empty dirty water tank.
Brush window is not latched in place.Unplug machine and reinstall window.
Debris channel in foot is clogged by debris.Clean the channel with a paper towel.
Filter clogged by debris.Remove debris clogging the filter screen and clean the filter.
Too much water applied.Go over area without spraying water.
Brush roll isn’t turningBrush roll is not installed properly.Follow instructions on page 10 for replacing brush roll.
Machine is standing upright.Recline machine to turn brush roll on.
Brush roll stalled by debris.Unplug machine and remove brush window and brush roll to remove obstruction.
Machine won’t turn ONBrush roll stalled by debris.Unplug machine and remove brush window and brush roll to remove obstruction.
Handle not inserted properly into body of machineReinsert handle and push down until it clicks in to place.
Machine is leakingCap of clean water tank is not closed properly.Remove the clean water tank and reapply the cap.

Note: Any other servicing should be performed by an authorized service representative.

Warranty

Limited 2-year warranty may vary by state. Visit support.BISSELL.com or call 1-800-237-7691 for complete warranty information.BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - thankyouBISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE CLEANER User Manual - logo

Download Manal PDF

BISSELL 3395 CrossWave ALL-IN-ONE MULTI-SURFACE
CLEANER User Manual PDF Download

Leave a comment

Your email address will not be published. Required fields are marked *