Oster 76023CL Cordless Fast Feed and Cordless Pro 700i User Manual

Oster 76023CL Cordless Fast Feed and Cordless Pro 700i User Manual

IMPORTANT SAFETY INFORMATION

Original Instructions
When using an electrical appliance, basic precautions are required to always be followed, including the following:
Read all instructions before using this appliance.
DANGER ­ To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.
   Unplug immediately from receptacle.
2. Do not use while bathing or in a shower.
3. Do not use when bathing an animal.
4. Do not place or store appliance where it is able to fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
5. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
6. Unplug this appliance before cleaning.

WARNING ­ To reduce the risk of burns, fire, electric shock or injury to persons:

1. An appliance shall never be left unattended when plugged in (does not apply to battery-operated models).
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not specified by the manufacturer.
4. Never operate this appliance when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been dropped into water. Return the appliance to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Keep the air openings free of lint, hair, and similar objects.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate while aerosol (spray) products are being used.
9. Do not use this appliance with a damaged or broken comb, as it has the potential to result in facial injury.
10. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to «OFF» (O) position then remove plug from outlet.
11. WARNING: Keep the appliance dry.
12. WARNING: Do not charge, place or leave the appliance where it is expected to be: a. Subject to damage by an animal, or b. Exposed to weather.
13. WARNING: Cutting blades may become hot after prolonged use.
14. WARNING: a. Plug charger directly into receptacle ­ do not use an extension cord.
    b. Unplug charger before plugging or unplugging appliance.
15. The appliance is only to be used with the power supply unit (Model No. PYS-050H200X001) provided.
16. This appliance contains batteries that are non-replaceable.
17. WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
18. Animal clipper and hair clipper can be used by children aged from 3 years under supervision.
19. Animal clipper and hair clipper can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
20. Children should not play with the appliance.
21. Cleaning and user maintenance should not be done by children without supervision.
22. WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
    SAVE THESE INSTRUCTIONS
    FOR ANIMAL CLIPPERS ONLY:
    The appliance is for trimming purposes only. Animal shearers can only be use by trained personnel.

ABOUT THE CLIPPER

DO NOT USE THIS APPLIANCE UNTIL YOU HAVE READ THESE OPERATING INSTRUCTIONS OPERATE ON VOLTAGE SPECIFIED ON APPLIANCE
HOW TO CHARGE THE UNIT
Place clipper on charging stand or connect directly to the power supply cord. This clipper has one control LED INDICATOR.

CHARGING WITH THE CHARGING STAND

1. Plug the power cord of the charging stand into an outlet with the rate voltage for your unit.
2.  Plug the other end into the charging stand. Note that the cord will only fit into the charging stand with the proper orientation.
3. Ensure that the switch on the unit is in the «OFF» (O) position.
4. Check the contacts of the trimmer and the battery for foreign particles and contamination.
5. Insert the trimmer into the charging stand so that the top of unit is facing you and the contacts on the trimmer are aligned with the contacts on the charging stand. The top of the unit is the side with the switch (Figure 1).
6. While the unit is being charged, the LED will pulse green until fully charged. Once the battery is fully charged, the LED will display a continuous green light and is ready for use.
7. If the LED light will not turn on, then re-insert the trimmer into the charging stand and push down gently on the trimmer to engage the contacts.
   Note: If the LED does not turn on then there may be dirt or grease on the contacts of the charging stand or trimmer. Clean the contacts with an approved cleaning solution and reinsert the trimmer into the charging stand. If the LED still fails to turn on then follow the return procedure under the warranty and service section.
8. The LEDs will stay on as long as the unit is in the charging stand.

ABOUT THE LI-ION BATTERY

1. This appliances operates with a Li-Ion 3.6V 2600mAh battery.
2. Note: To ensure that the new battery reaches its full potential, the battery should be completely drained after the first use. This operation will only have to be performed 3 times.
3. To ensure the longevity of this powerful battery the trimmer must be operated with properly cleaned, sharpened and oiled blades at all times.
4. When the battery is fully charged, the trimmer can be used for 90 minutes without being connected to the power supply.
5. For instructions on disposal of the Li-Ion battery please refer to the “WASTE DISPOSAL” section at end of this manual.

OPERATING THE UNIT

The appliance is designed to operate in either cordless or corded mode. The preferred method is cordless as it ensures a longer life for the battery. Use the power cord when the batteries are not fully charged. If your appliance did not come with a charging stand please refer to corded operation in this manual. Always apply one to two drops of the provided Oster™ Clipper & Blade Lubricating Oil or other Oster™ approved lubricant to the blades before use. Wipe off excess with a clean dry cloth. When finished using, clean excess hair from the blades using the cleaning brush and wipe the housing with a clean dry cloth. Before replacing the blade guard for storage, disperse one or two drops of lubricating oil over the blades to prevent rusting. Cutting efficiency may drop and the blades and motor may be damaged if hair is dirty or hair styling agents have been applied. Always ensure that hair is clean before using the appliance. Keep the cord straight while in use. If the cord becomes kinked or tangled, turn «OFF» (O) the appliance and straighten it. The A-weighted sound pressure level emitted by this product is below 70db. The vibration total value to which the hand-arm system is subjected, measured according to EN ISO 5349-1 and EN ISO 5349-2, is below 2,5 m/s².

CORDLESS OPERATION

1. Remove the appliance from the charging stand. (See section titled “HOW TO CHARGE THE UNIT” before initial use).
2. Turn the appliance «ON» (|) using the switch located on the front of the unit and use the appliance. If the appliance does not turn «ON» (|), then the battery may be fully depleted and may have to be partially charged prior to re-use.
3. Turn the appliance «OFF» (O) when finished using. 4) Insert appliance into charging stand or plug into the power cord.

MAINTENANCE

STORAGE

1. Store your appliance in a clean, dry space.
2. Do not wrap the cord around the appliance when storing. This can damage the cord insulation.
3. Always take care not to tangle the cord while using or storing the appliance.
4. We recommend storing the appliance and cord in the original carton when not in use.

BLADE CARE

ADJUSTABLE BLADE CLIPPERS

TO ADJUST: Move blade adjustment lever down for closer cutting (size 000 or 30), and up for longer cutting (size 1, or 10)

REMOVING OR REPLACING BLADES

IMPORTANT: Make sure the appliance is turned off and unplugged before removing any part.
TO REMOVE: To remove the blades, unplug the clipper from the electric outlet. Lay the unit upside down on a flat, dry surface. Remove the two screws located in the bottom of the blade.

TO REPLACE: To replace blades, put the new top blade into position on the clipper head. Make sure the adjustment lever is pushed downward. Line up the new bottom blade so that the screw holes in the bottom blade are directly over the two center screw holes in the mounting plate. Replace the screws. Before tightening the screws adjust the position of the blades so that the top blade is 1/32″ back from and is parallel to the front edge of the bottom blade. The blades should also be even on each side. Tighten screws firmly.

LUBRICATING THE BLADES

Blades should be oiled regularly to reduce heat, maintain sharpness and will extend run time per battery charge cycle by reducing friction. Before removing the blade, be sure it has cooled down and the appliance is unplugged. Carefully slide the upper blade left or right to apply one or two drops of provided Oster™ Clipper & Blade Lubricating Oil or other Oster™ approved lubricant on each running rail of the lower blade. Excess oiling will cause hair to stick between teeth, slowing or jamming blades. Wipe excess oil with a dry, soft cloth.

BLADE SHARPENING

Oster™ cutting blades are of individual hollow-ground design, hardened to extend cutting life. As with any cutting instrument, the cutting edges will become dull with usage. Increasing blade tension to force dull blades to cut can cause the appliance to heat and reduce motor life, and further shorten blade life. When the cutting blades no longer cut smooth and clean, sharpening is necessary. When sharpening blades becomes necessary, send blades to an Oster™ Authorized Service Center where approved methods, equipment and proper knowledge are used to restore the original hollow-ground design and cutting ability. DO NOT sharpen blades by flat grinding or any method contrary to the design and construction of Oster™ cutting blades.

CLEANING

USING THE ATTACHMENTS:

Plastic combs for attachment to clippers and trimmer blades are included with some kits. This plastic comb serves as a clipping guide so that the hair is not clipped short. The comb attachment is grooved to fit snugly over the blades. When attaching the comb to the clipper or trimmer, slide the comb down firmly as far as it will go. Make sure the comb is seated securely against the lower blade. To disengage the comb, pull and slide the comb upward until it is off the clipper or trimmer. Replacement combs are not covered under warranty.

BLADES

To clean the blades, fill a flat dish with Oster™ Blade Wash® cleaning solution and immerse only the blade teeth. DO NOT IMMERSE THE APPLIANCE. Turn «ON» (|) the appliance with the blades facing down. Do not hold the appliance upright when cleaning blades with the appliance plugged in. Listen for a change in the hum of the motor. As the build-up is removed, the clean blade runs faster and at a higher pitch. When the pitch stabilizes (between 30 to 60 seconds), turn «OFF» (O) the appliance and unplug. Remove from the cleaning solution and, while holding the appliance with the blade end facing down, wipe the blades dry with a clean, dry cloth. Re-oil blades. Always unplug the appliance when carrying out other cleaning and do not immerse the appliance body, charging stand, adapter, power cord or plug in water or any other liquid.

CHARGING STATION

1. Disconnect the charging station from the power supply.
2. If necessary, remove hairs from both charging cavities.
3. If dirty, clean the contacts with a dry cloth.

CONTACTS

If required, clean the contacts of the trimmer and charging sand with a dry cloth. Any maintenance beyond the cleaning and lubricating instructions in this manual should be performed by an Oster™ Authorized Service Center. The tasks described here for troubleshooting can be done mostly by the operator. Some tasks only may be done by specially trained personnel or by an Oster™ authorized service center. These tasks are marked with (*).

⚠ WARNING When using or cleaning this appliance, do not use any aerosol sprays or blade washes, especially those containing methylene chloride, dimethyl benzyl ammonium chloride, or 1-1-1 trichloroethylene. Damage caused by these chemicals will void your warranty. You may use Oster™ approved blade washes, lubricants and disinfectant sprays that do not harm the product.

TROUBLE SHOOTING

The tasks described here for troubleshooting can be done mostly by the operator. Some tasks only may be done by specially trained personnel or by an Oster™ authorized service center. These tasks are marked with (*).

WASTE DISPOSAL

WARNING BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

1. The battery must be removed from the appliance before it is scrapped.
2. The appliance must be disconnected from the supply mains when removing the battery.
3. The battery is to be recycled or disposed of safely.
4. For battery removal or maintenance please contact an Oster™ Authorized Service Center.

Disposal in E.U. countries
Do not dispose of the appliance with domestic refuse and do not throw them into fire or water. As part of the E.U. Directive governing the disposal of electric and electronic appliances, the appliance is accepted free of charge by local waste collection points or recycling centres. Correct disposal will ensure environment protection and prevent a potential harmful impact on people and the environment.
Disposal in non-E.U. countries Please dispose of the appliance at the end of service life in an environmentally friendly manner, per applicable local and national laws and regulations.

AFTER SALES AND REPLACEMENT PARTS

In the case the appliance does not operate but is under warranty, return the product to the place it was purchased for a replacement. Please be aware that a valid form of proof of purchase will be required. For additional support, please contact our Consumer Service Department at: + 49 (0) 6190-93443-0. International rates may apply. Alternatively,
e-mail: [email protected].

For service, please contact:
Europe, Africa and Middle East:
Oster™ GmbH
Am Eisernen Steg 20, D-65795 Hattersheim am Main, Germany
[email protected]
+49 (0) 6190-93443-0
Latin America:
Sunbeam Latin America, LLC.
5200 Blue Lagoon Drive, Suite 860
Miami, FL 33126
[email protected]
+1 (786) 845-2540
North America:
OsterTM Direct® Services
904 Red Road, McMinnville, TN 37110
(800) 830-3678
or an Authorised Service Centre
Please visit our websites for information about your local OsterTM authorised
distributor:
WWW.OSTERSTYLE.COM
WWW.OSTERPRO.COM

©2021 Jarden Consumer Solutions (Europe) Limited. All rights reserved. Jarden Consumer Solutions (Europe) Limited, 5400 Lakeside, Cheadle Royal Business Park, Cheadle, Cheshire, SK8 3GQ, United Kingdom. In Europe: Imported and distributed by OsterTM GmbH, Am Eisernen Steg 20, D-65795 Hattersheim am Main, Germany. [email protected].
Jarden Consumer Solutions (Europe) Limited is a subsidiary of Newell Brands Inc. Due to continuous product development, the product inside the packaging may differ slightly from the one shown on the packaging.
Printed in China.