PowMr 10A 12V 24V PWM Solar Charge Controller with
light-operated User Manual
SAFETY INSTRUCTIONS
- Make sure your battery has enough voltage for the controller to recognize the battery type before first installation.
- The battery cable should be as short as possible to minimize loss.
- This controller is suitable for all kinds of lead-acid batteries (including Sealed, Flooded, AGM, GEL), lithium ion batteries, and lithium iron phosphate batteries.
- The charge regulator is only suitable for regulating solar modules. Never connect another charging source to the charge regulator
PRODUCT FEATURES
- Build-in industrial micro controller.
- IR remote control, LED display, auto memory function, IP68 protection.
- Fully 4-stage PWM charge management.
- Build-in short-circuit protection, open-circuit protection, reverse protection, over-load protection.
- Dual mosfet Reverse current protection, low heat production.
SYSTEM CONNECTION
- Connect the battery to the charge regulator – plus and minus. it will auto adapt the battery type.
- Connect the photovoltaic module to the regulator – plus and minus.
- Connect the consumer to the charge regulator – plus and minus
The reverse order applies when uninstalling!
An improper sequence order can damage the controller!
SETTING/SYSTEM MODE
- When the controller is energized, the controller recognizes the battery voltage type. If the battery voltage is lower than 18V, it is identified as the 12V system, and
if it is higher than 18V, it is identified as the 24V system. - After identifying the system voltage, the user can press the infrared remote controller to choose a battery type. After receiving the signal, the controller’s blue light flashes and the setting is completed without restarting.
- the controller supports 3 types of batteries, which is: 12V lead-acid batteries (including Sealed, Flooded, AGM, GEL)11.1V lithium ion battery (3 series, 3*3.7V, including capacity and power type). 12.8V phosphoric acid iron lithium battery (4 series, 4*3.2V) If it is a 24V system, it corresponds to: 24V lead-acid batteries (including Sealed, Flooded, AGM, GEL) 22.2V lithium ion battery (6 series, 6*3.7V, including capacity and power type). 25.6V phosphoric acid iron lithium battery (8 series, 8*3.2V)
- after the battery type is set, then user can set the work mode of the load, the system (24H) mode is normally open mode for the load, which means, the load output has been always connected (unless low power protection). Dusk to Dawn mode (D2D) means system load is disconnected in the daytime and connected at the night time. 1-13H means system load is connected when night falls and disconnected after 1-13 hours timer. The D2D mode and the timer mode are used for solar energy lighting system, which is fully automatic control.
- when it is necessary to temporarily connect or disconnect the load, press the manual (H), enter the manual mode, and then press ON/OFF to manually switch the load,.this function is generally used to test the connection of the load.
TROUBLE SHOOTING
| Situation | Probable cause | Solution |
| Charge LED not on when sunny | Solar panel opened or reversed |
Reconnect |
| Load LED off | Mode setting wrong | Set again |
| Battery low | recharge | |
| Load LED slow flashing | Over load | Reduce load watt |
| Load LED slow flashing | Short circuit protection | Auto reconnect |
| Power off | Battery too low/reverse | Check battery/connection |
TECHNICAL PARAMETER
| MODEL | IR-A | IR-B | IR-C |
| Size | 82*45*21mm | 82*58*21mm | 82*58*21mm8 |
| Installing hole size | 74.5mm | 74.5*44.4mm | 74.5*44.4mm |
| weight | 120g | 135g | 150g |
| Remote function | NO | YES | YES |
| USB | NO | NO | 5V/2A |
| Battery voltage | 12V/24V auto adapt | ||
| Rated current | 5-20A | ||
| Max Solar input | 50V | ||
| Battery type | Lead-acid | Lithium ion | LiFePO4 |
| Equalization | 14.4V | – | – |
| ABS | 14.2V | – | – |
| Float | 14.2V | 12.6V | 14.4V |
| Discharge stop | 11.2V | 9V | 10V |
| Discharge reconnect | 12.6V | 10.5V | 12V |
| Self-consume | <10mA | ||
| Voltage of open light | Solar panel 8V（delay 10s） | ||
| Voltage of close light | Solar panel 8V（delay 60s） | ||
| Operating temperature | -20~+60 ℃ | ||
*all red color voltage X2 while using 24V system
*Product specifications are subject to change without prior notice
Download Manual PDF
PowMr 10A 12V 24V PWM Solar Charge Controller with
light-operated User Manual PDF Download
