SWISS Waves Wireless Headphone User Manual
SPECS FOR PRODUCTS
Bluetooth version : Bluetooth V5.3
Chipset: Bluetrum
Frequency: 2.4-2.48354G (Hz)
Transmission Distance: 1 Om
Battery Capacity: 3. 7V /200mAH
Charging Time: about 1.5-2 hour
Charging Voltage: DC 5V
Working temperature: -40° to +85″
Playtime (100%volume): 5 hours
Standby time: about 300 hours
Speaker Section
Speaker Dimension: <D40mm
Impedance: 320
Sensitivity: 108dB+/-3dB
Frequency Response: 20-20KHz
FUNCTION DESCRIPTION
Power On of device: Long press ON OFF about 3 seconds on, prompt “Power on”.
Power off of device: Long press ON OFF about 3 seconds on prompt “Power off”.
BLUETOOTH PAIRING
- Power the headphones ON, boot into pairing mode automatically, prompt “the Bluetooth device is ready to pair”, and the LED indicator will flash BLUE and RED.
- Set your mobile device to search for Bluetooth devices. Select “Swiss brand Waves” from the list of found devices.
- After a successful pairing, a Prompt “The Bluetooth device is connected successfully” will be heard. The LED indicator will begin flashing BLUE intermittently while connected.
In Bluetooth pairing mode, playback and volume can be adjusted with the on-ear controls, or with your paired device.
CONTROLS RIGHT HEADPHONE
- Power ON/OFF
- Vol + /Next Track
- Pause and resume playback/Answer/End phone call/SIRI assist
- Vol – /Previous Track
- Microphone
- LED Indicator
- TYPE-C charging port
- 3.5mm AUX port
WIRELESS HEADPHONES FUNCTIONS
Get through ——————————–Short press 
Hang up ————————-In a call short press
Replay the last phone number ———–2x press
Play/Pause Music ——————–Short press
Going to SIRI assist ——————–Long press 2 seconds
Volume control to up and down —-Long press (+) / (-)
Song switch to next and previous track ———-Short press(+)/ (-)
ANSWER/END/REJECT INCOMING CALLS
To use the phone functions on the headphones, you must be connected to a Bluetooth-enabled device.
- Press the
button to answer and end phone calls, Playback will automatically pause and resume. - 2x press the button to dial the last outgoing phone number.
- Press and hold the button for about 3 seconds to reject an incoming call.
LED LIGHT STATUS
- Charging status —– Long bright red light, full charged red light was off.
- Power on—– Flash blue then Red and blue LED indicator flash alternately.
- Pairing status—–Red and blue LED indicator flash alternately
- Already connected status— Flashing blue light per 3 seconds
- Play status—–LED indicator will flashing BLUE intermittently.
MATTERS ATTENTION
Low battery prompt: prompt: “Battery Low”.
CHARGING INSTRUCTION
Connect the Type C cable to headphones and power source.
FCC STATEMENT
NOTE: This equipment has been tasted and found lo comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed lo provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can he determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment This device complies with Part 15 of lie FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
THIS IS A BATTERY-OPERATED PRODUCT. THIS IS NOT A TOY. INTENDED USE OF THE PRODUCT SHOULD NOT RESULT IN EXPOSURE TO THE BATTERY. In case of rupture, the below hazards exist.
Harmful if swallowed. Causes skin irritation. Causes eye irritation. May cause respiratory irritation.
Proper Handling:
Do not open, disassemble, crush, or burn battery. Do not handle battery in a manner that allows terminal to short circuit. Avoid mechanical damage of the battery. Battery may explode or cause burns, if disassembled, crushed, or exposed to fire or high temperature. Do not short or install with incorrect polarity. Avoid all personal contact, including inhalation. Wear protective
clothing when risk of exposure occurs. Use in a well-ventilated area. Prevent concentration in hollows and sumps.
Proper Storage:
Store in a cool, dry, well-ventilated area. Keep away from heat and direct sunlight.
Disposal considerations:
Recycle in accordance with government, state and local regulations, to ensure proper disposal.
If exposed to the battery- potential health effect and first aid measures:
After eye contact:
Flush eyes cautiously with plenty of water for several minutes while holding eyelids open.
Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation persists.
After skin contact:
Remove contaminated clothing and shoes. Immediately wash with water and soap and rinse thoroughly. Wash clothing and shoes before reuse. If irritation occurs, get medical attention.
After inhalation:
Remove person to fresh air and keep comfortable for breathing. Administer artificial respiration if breathing is difficult. Seek medical attention.
After swallowing:
Rinse mouth with water. Do not induce vomiting. Get medical attention.
Battery may burst and release hazardous decomposition products when exposed to a fire situation. Lithium-ion batteries contain flammable electrolyte that may vent, ignite, and product sparks when subjected to high temperature (>302°) (>150°C), when damaged or abused (e.g. mechanical damage or electrical overcharging), may burn rapidly with flare-burning effect, may ignite other batteries in close proximity. Specific protective actions for fire-fighters:
Wear positive pressure self-contained breathing apparatus (SCBA). Structural firefighters’ protective clothing will only provide limited protection.
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
Do not touch or walk through spilled material. Absorb with earth, sand, or other non-combustible materials. Leaking batteries and contaminated absorbent material should be placed in metal containers.
Suitable fire-extinguishing media:
Small fire: dry chemical, CO2, water spray, or regular foam.
Large fire: water spray, fog, or regular foam.
Questions? Comments? Contact [email protected]
