HyperX Cloud 2 Gaming Headset User Manual
HyperX Cloud 2 Overview
- Mic mute button
- Power button
- Analog headphone port
- USB charge port
- Microphone port
- Volume wheel
- Detachable microphone
- Wireless adapter
- Wireless status light
- USB charge cable
It is recommended to fully charge your headset before first use.
When the charge cable is connected the ear cup LED will indicate the status.
|CHARGE STATUS||EAR CUP LED|
Power on/off – Hold power button for 3 seconds
LED effect – Short press power button to toggle ear cup LED pattern between on/breathing effect/off
Use with PS5™ Console
- Connect the wireless USB adapter to PS5™. (The wireless status light will blink.)
- Power on the headset.
- When the wireless adapter status light is solid the headset is connected.
PlayStation 5 Audio Settings
Settings > Sound
Input Device: USB Headset (HyperX Cloud Flight for PS)
Output Device: USB Headset (HyperX Cloud Flight for PS)
Output to headphones: All Audio
Questions or setup issues?
Contact the HyperX support team or see the user manual at: hyperxgaming.com/support/headsets
Simplified Declaration of Conformity
Hereby, HP declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.hp.eu/certificates (search with Model Name)
UK only: Hereby, HP declares that the radio equipment is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: www.hp.eu/certificates (search with Model Name)
Battery/TX Power Info
|Contains 3.7 V, 1500 mAh Li-ion Battery, 5.55Wh|
Cannot be replaced by user
|Frequency & TX Power Information|
|Frequency Bands: 2.4GHz (TX Power 1.5dBm ≤ TX ≤ 3.5dBm)|
Is this headset compatible with the Xbox One X|S and Series X|S?
This headset is only compatible when connecting it directly to the controller via the 3.5mm jack. Note that the sound will be in Stereo as 7.1 Surround Sound does not work when connected via 3.5mm jack.
Is this headset compatible with the PS4, PS5 and the Nintendo Switch consoles?
Yes, you can connect to the PS4, PS5 and Switch consoles via 3.5mm jack or USB. To ensure full compatibility of the USB sound card, update the firmware to version 0010 – available on the HyperX website. A PC is required to perform the update.
Will the Cloud II headset work with my mobile device?
The Cloud II headset will work on mobile devices that accept a CTIA 4 pole TRRS 3.5mm jack. There are two standards, CTIA and OMTP. Please check with your mobile devices manufacturer for compatibility.
Is there mic monitoring on the Cloud II headset?
No, the Cloud II headset does not have built-in mic monitoring.
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the users encouraged to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment FCC ID: B94-CF001
This Class B digital apparatus complies with Canadian ICES-003.
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
India RoHS Statement
This product, as well as its related consumables and spares, complies with the reduction in hazardous substances provisions of the “India E-waste (Management and Handling) Rule 2016.” It does not contain lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for where allowed pursuant to the exemptions set in Schedule 2 of the Rule.
©Copyright 2022 HyperX and the HyperX logo are registered trademarks or trademarks of HP Inc. in the U.S. and/or other countries. All registered trademarks and trademarks are
property of their respective owners.